1 votes

Mike Wazowski avatar

Disque dur externe détecté, mais non reconnu. Impossible de monter, de formater, de faire une partition.

Demandé el 20 de Décembre, 2016
Quand la question a-t-elle été
8726 affichage
Nombre de visites la question a
2 Réponses
Nombre de réponses aux questions
Résolu
Situation réelle de la question

Je suis nouveau sur ubuntu et dans cette communauté. J'ai un disque dur externe Seagate Expansion (1 To) qui a besoin d'être sauvé. Tout d'abord, il s'est planté il y a quelques temps. A ce moment-là, je pouvais utiliser un logiciel de récupération de données pour récupérer mes données. Mais j'étais impatient pour un processus de récupération de données de 10 jours et donc j'ai débranché le lecteur. Par la suite, Windows a cessé de reconnaître le disque. Assez récemment, j'ai été la recherche en ligne pour trouver le lecteur pourrait être reconnu par ubuntu et heureusement il a fait. Mais le problème est que ni je peux créer une image disque, ni le formater, ni faire des partitions. il ne monte pas. J'ai fait des recherches approfondies pour trouver la cause exacte de l'erreur. J'ai lancé la commande dmesg et j'ai recueilli quelques informations. Les informations pertinentes sont les suivantes :

[   33.024928] usb 2-1: new SuperSpeed USB device number 2 using xhci_hcd
[   33.043698] usb 2-1: New USB device found, idVendor=0bc2, idProduct=2321
[   33.043701] usb 2-1: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[   33.043702] usb 2-1: Product: Expansion
[   33.043703] usb 2-1: Manufacturer: Seagate 
[   33.043705] usb 2-1: SerialNumber: NA4AT906
[   33.055276] usb-storage 2-1:1.0: USB Mass Storage device detected
[   33.055796] scsi host4: usb-storage 2-1:1.0
[   33.055897] usbcore: registered new interface driver usb-storage
[   33.057513] usbcore: registered new interface driver uas
[   34.053914] scsi 4:0:0:0: Direct-Access     Seagate  Expansion        0219 PQ: 0 ANSI: 6
[   34.054233] sd 4:0:0:0: Attached scsi generic sg1 type 0
[   55.120163] sd 4:0:0:0: [sdb] Spinning up disk...
[   59.640823] usb 2-1: Disable of device-initiated U1 failed.
[   59.644262] usb 2-1: Disable of device-initiated U2 failed.
[   60.367518] usb 2-1: USB disconnect, device number 2
[   61.380448] .ready
[   61.380624] sd 4:0:0:0: [sdb] Read Capacity(10) failed: Result: hostbyte=DID_NO_CONNECT driverbyte=DRIVER_OK
[   61.380628] sd 4:0:0:0: [sdb] Sense not available.
[   61.380662] sd 4:0:0:0: [sdb] Write Protect is off
[   61.380673] sd 4:0:0:0: [sdb] Mode Sense: 00 00 00 00
[   61.380709] sd 4:0:0:0: [sdb] Asking for cache data failed
[   61.380722] sd 4:0:0:0: [sdb] Assuming drive cache: write through
[   61.381302] sd 4:0:0:0: [sdb] Read Capacity(10) failed: Result: hostbyte=DID_NO_CONNECT driverbyte=DRIVER_OK
[   61.381304] sd 4:0:0:0: [sdb] Sense not available.
[   61.381317] sd 4:0:0:0: [sdb] Attached SCSI disk
[  116.391733] systemd[1]: apt-daily.timer: Adding 17min 55.120014s random time.
[  180.155884] usb 2-1: new SuperSpeed USB device number 3 using xhci_hcd
[  180.172597] usb 2-1: New USB device found, idVendor=0bc2, idProduct=2321
[  180.172601] usb 2-1: New USB device strings: Mfr=2, Product=3, SerialNumber=1
[  180.172603] usb 2-1: Product: Expansion
[  180.172605] usb 2-1: Manufacturer: Seagate
[  180.172607] usb 2-1: SerialNumber: 2HC015KJ
[  180.174591] scsi host5: uas
[  180.176468] scsi 5:0:0:0: Direct-Access     Seagate  Expansion        0502 PQ: 0 ANSI: 6
[  180.176973] sd 5:0:0:0: Attached scsi generic sg1 type 0
[  180.177288] sd 5:0:0:0: [sdb] Spinning up disk...
[  181.178895] ................................................................................
[  261.140098] usb 2-1: USB disconnect, device number 3
[  261.426865] .ready
[  261.586851] sd 5:0:0:0: [sdb] Read Capacity(16) failed: Result: hostbyte=DID_ERROR driverbyte=DRIVER_OK
[  261.586854] sd 5:0:0:0: [sdb] Sense not available.
[  261.706802] sd 5:0:0:0: [sdb] Read Capacity(10) failed: Result: hostbyte=DID_ERROR driverbyte=DRIVER_OK
[  261.706806] sd 5:0:0:0: [sdb] Sense not available.
[  261.794720] sd 5:0:0:0: [sdb] Write Protect is off
[  261.794723] sd 5:0:0:0: [sdb] Mode Sense: 00 00 00 00
[  261.834688] sd 5:0:0:0: [sdb] Asking for cache data failed
[  261.834692] sd 5:0:0:0: [sdb] Assuming drive cache: write through
[  262.062590] sd 5:0:0:0: [sdb] Read Capacity(16) failed: Result: hostbyte=DID_ERROR driverbyte=DRIVER_OK
[  262.062594] sd 5:0:0:0: [sdb] Sense not available.
[  262.182519] sd 5:0:0:0: [sdb] Read Capacity(10) failed: Result: hostbyte=DID_ERROR driverbyte=DRIVER_OK
[  262.182522] sd 5:0:0:0: [sdb] Sense not available.
[  262.422368] sd 5:0:0:0: [sdb] Attached SCSI disk
[  275.958597] usb 2-2: new SuperSpeed USB device number 4 using xhci_hcd
[  275.975347] usb 2-2: New USB device found, idVendor=0bc2, idProduct=2321
[  275.975351] usb 2-2: New USB device strings: Mfr=2, Product=3, SerialNumber=1
[  275.975353] usb 2-2: Product: Expansion
[  275.975355] usb 2-2: Manufacturer: Seagate
[  275.975356] usb 2-2: SerialNumber: 2HC015KJ
[  275.977125] scsi host6: uas
[  275.977598] scsi 6:0:0:0: Direct-Access     Seagate  Expansion        0502 PQ: 0 ANSI: 6
[  275.978151] sd 6:0:0:0: Attached scsi generic sg1 type 0
[  275.978258] sd 6:0:0:0: [sdb] Spinning up disk...
[  276.977994] ...................................................................................................
[  376.245447] usb 2-2: USB disconnect, device number 4
[  376.245528] sd 6:0:0:0: tag#0 uas_zap_pending 0 uas-tag 1 inflight: CMD 
[  376.245531] sd 6:0:0:0: tag#0 CDB: Test Unit Ready 00 00 00 00 00 00
[  376.245554] ready
[  376.361931] sd 6:0:0:0: [sdb] Read Capacity(16) failed: Result: hostbyte=DID_ERROR driverbyte=DRIVER_OK
[  376.361935] sd 6:0:0:0: [sdb] Sense not available.
[  376.482049] sd 6:0:0:0: [sdb] Read Capacity(10) failed: Result: hostbyte=DID_ERROR driverbyte=DRIVER_OK
[  376.482052] sd 6:0:0:0: [sdb] Sense not available.
[  376.570129] sd 6:0:0:0: [sdb] Write Protect is off
[  376.570132] sd 6:0:0:0: [sdb] Mode Sense: 00 00 00 00
[  376.610165] sd 6:0:0:0: [sdb] Asking for cache data failed
[  376.610169] sd 6:0:0:0: [sdb] Assuming drive cache: write through
[  376.842367] sd 6:0:0:0: [sdb] Read Capacity(16) failed: Result: hostbyte=DID_ERROR driverbyte=DRIVER_OK
[  376.842370] sd 6:0:0:0: [sdb] Sense not available.
[  376.962439] sd 6:0:0:0: [sdb] Read Capacity(10) failed: Result: hostbyte=DID_ERROR driverbyte=DRIVER_OK
[  376.962442] sd 6:0:0:0: [sdb] Sense not available.
[  377.162638] sd 6:0:0:0: [sdb] Attached SCSI disk
[  383.263500] usb 2-2: new SuperSpeed USB device number 5 using xhci_hcd
[  383.280228] usb 2-2: New USB device found, idVendor=0bc2, idProduct=2321
[  383.280232] usb 2-2: New USB device strings: Mfr=2, Product=3, SerialNumber=1
[  383.280234] usb 2-2: Product: Expansion
[  383.280236] usb 2-2: Manufacturer: Seagate
[  383.280238] usb 2-2: SerialNumber: 2HC015KJ
[  383.282026] scsi host7: uas
[  383.283790] scsi 7:0:0:0: Direct-Access     Seagate  Expansion        0502 PQ: 0 ANSI: 6
[  383.284411] sd 7:0:0:0: Attached scsi generic sg1 type 0
[  383.284438] sd 7:0:0:0: [sdb] Spinning up disk...
[  384.288132] ..............................
[  414.341158] usb 2-2: USB disconnect, device number 5
[  414.426199] .ready
[  414.586320] sd 7:0:0:0: [sdb] Read Capacity(16) failed: Result: hostbyte=DID_ERROR driverbyte=DRIVER_OK
[  414.586323] sd 7:0:0:0: [sdb] Sense not available.
[  414.706355] sd 7:0:0:0: [sdb] Read Capacity(10) failed: Result: hostbyte=DID_ERROR driverbyte=DRIVER_OK
[  414.706360] sd 7:0:0:0: [sdb] Sense not available.
[  414.794375] sd 7:0:0:0: [sdb] Write Protect is off
[  414.794379] sd 7:0:0:0: [sdb] Mode Sense: 00 00 00 00
[  414.834391] sd 7:0:0:0: [sdb] Asking for cache data failed
[  414.834395] sd 7:0:0:0: [sdb] Assuming drive cache: write through
[  415.062455] sd 7:0:0:0: [sdb] Read Capacity(16) failed: Result: hostbyte=DID_ERROR driverbyte=DRIVER_OK
[  415.062458] sd 7:0:0:0: [sdb] Sense not available.
[  415.182491] sd 7:0:0:0: [sdb] Read Capacity(10) failed: Result: hostbyte=DID_ERROR driverbyte=DRIVER_OK
[  415.182495] sd 7:0:0:0: [sdb] Sense not available.
[  415.382544] sd 7:0:0:0: [sdb] Attached SCSI disk
[  436.159245] usb 2-2: new SuperSpeed USB device number 6 using xhci_hcd
[  436.175831] usb 2-2: New USB device found, idVendor=0bc2, idProduct=2321
[  436.175834] usb 2-2: New USB device strings: Mfr=2, Product=3, SerialNumber=1
[  436.175836] usb 2-2: Product: Expansion
[  436.175837] usb 2-2: Manufacturer: Seagate
[  436.175838] usb 2-2: SerialNumber: 2HC015KJ
[  436.177490] scsi host8: uas
[  436.178528] scsi 8:0:0:0: Direct-Access     Seagate  Expansion        0502 PQ: 0 ANSI: 6
[  436.179064] sd 8:0:0:0: Attached scsi generic sg1 type 0
[  436.179388] sd 8:0:0:0: [sdb] Spinning up disk...
[  437.183342] ..ready
[  438.187867] sd 8:0:0:0: [sdb] 1953525167 512-byte logical blocks: (1.00 TB/932 GiB)
[  438.187871] sd 8:0:0:0: [sdb] 2048-byte physical blocks
[  438.401354] sd 8:0:0:0: [sdb] Write Protect is off
[  438.401359] sd 8:0:0:0: [sdb] Mode Sense: 4f 00 00 00
[  438.404691] usb 2-2: cmd cmplt err -71
[  438.404695] xhci_hcd 0000:00:14.0: ERROR Transfer event for disabled endpoint or incorrect stream ring
[  438.404698] xhci_hcd 0000:00:14.0: @000000003fb70700 00000000 00000000 04000000 08078001
[  439.135787] usb 2-2: USB disconnect, device number 6
[  439.136027] sd 8:0:0:0: tag#0 uas_zap_pending 0 uas-tag 1 inflight: CMD 
[  439.136036] sd 8:0:0:0: tag#0 CDB: Mode Sense(6) 1a 00 08 00 04 00
[  439.136109] sd 8:0:0:0: [sdb] Asking for cache data failed
[  439.136119] sd 8:0:0:0: [sdb] Assuming drive cache: write through
[  439.363764] sd 8:0:0:0: [sdb] Read Capacity(16) failed: Result: hostbyte=DID_ERROR driverbyte=DRIVER_OK
[  439.363767] sd 8:0:0:0: [sdb] Sense not available.
[  439.483784] sd 8:0:0:0: [sdb] Read Capacity(10) failed: Result: hostbyte=DID_ERROR driverbyte=DRIVER_OK
[  439.483787] sd 8:0:0:0: [sdb] Sense not available.
[  439.723819] sd 8:0:0:0: [sdb] Attached SCSI disk
[  453.361652] usb 2-2: new SuperSpeed USB device number 7 using xhci_hcd
[  453.378371] usb 2-2: New USB device found, idVendor=0bc2, idProduct=2321
[  453.378373] usb 2-2: New USB device strings: Mfr=2, Product=3, SerialNumber=1
[  453.378375] usb 2-2: Product: Expansion
[  453.378376] usb 2-2: Manufacturer: Seagate
[  453.378377] usb 2-2: SerialNumber: NA4AT906
[  453.380046] scsi host9: uas
[  453.380499] scsi 9:0:0:0: Direct-Access     Seagate  Expansion        0502 PQ: 0 ANSI: 6
[  453.381082] sd 9:0:0:0: [sdb] 1953525167 512-byte logical blocks: (1.00 TB/932 GiB)
[  453.381084] sd 9:0:0:0: [sdb] 4096-byte physical blocks
[  453.381695] sd 9:0:0:0: Attached scsi generic sg1 type 0
[  453.842067] sd 9:0:0:0: [sdb] Write Protect is off
[  453.842071] sd 9:0:0:0: [sdb] Mode Sense: 4f 00 00 00
[  453.842272] sd 9:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[  453.853509]  sdb: sdb1
[  453.854847] sd 9:0:0:0: [sdb] Attached SCSI disk
[  501.001736] sd 9:0:0:0: [sdb] Synchronizing SCSI cache
[  501.118525] sd 9:0:0:0: [sdb] Synchronize Cache(10) failed: Result: hostbyte=DID_ERROR driverbyte=DRIVER_OK
[  501.153024] usb 2-2: USB disconnect, device number 7
[  501.527014] usb 2-2: new SuperSpeed USB device number 8 using xhci_hcd
[  501.543688] usb 2-2: New USB device found, idVendor=0bc2, idProduct=2321
[  501.543690] usb 2-2: New USB device strings: Mfr=2, Product=3, SerialNumber=1
[  501.543692] usb 2-2: Product: Expansion
[  501.543693] usb 2-2: Manufacturer: Seagate
[  501.543694] usb 2-2: SerialNumber: NA4AT906
[  501.545329] scsi host10: uas
[  501.546356] scsi 10:0:0:0: Direct-Access     Seagate  Expansion        0502 PQ: 0 ANSI: 6
[  501.546876] sd 10:0:0:0: Attached scsi generic sg1 type 0
[  501.547082] sd 10:0:0:0: [sdb] 1953525167 512-byte logical blocks: (1.00 TB/932 GiB)
[  501.547085] sd 10:0:0:0: [sdb] 4096-byte physical blocks
[  501.547394] sd 10:0:0:0: [sdb] Write Protect is off
[  501.547397] sd 10:0:0:0: [sdb] Mode Sense: 4f 00 00 00
[  501.547554] sd 10:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[  503.618587]  sdb: sdb1
[  503.619863] sd 10:0:0:0: [sdb] Attached SCSI disk
[  513.448650] sd 10:0:0:0: [sdb] Synchronizing SCSI cache
[  513.571824] sd 10:0:0:0: [sdb] Synchronize Cache(10) failed: Result: hostbyte=DID_ERROR driverbyte=DRIVER_OK
[  513.604864] usb 2-2: USB disconnect, device number 8
[  513.980307] usb 2-2: new SuperSpeed USB device number 9 using xhci_hcd
[  513.996960] usb 2-2: New USB device found, idVendor=0bc2, idProduct=2321
[  513.996962] usb 2-2: New USB device strings: Mfr=2, Product=3, SerialNumber=1
[  513.996964] usb 2-2: Product: Expansion
[  513.996965] usb 2-2: Manufacturer: Seagate
[  513.996966] usb 2-2: SerialNumber: NA4AT906
[  513.998656] scsi host11: uas
[  513.999666] scsi 11:0:0:0: Direct-Access     Seagate  Expansion        0502 PQ: 0 ANSI: 6
[  514.000116] sd 11:0:0:0: Attached scsi generic sg1 type 0
[  514.000871] sd 11:0:0:0: [sdb] 1953525167 512-byte logical blocks: (1.00 TB/932 GiB)
[  514.000873] sd 11:0:0:0: [sdb] 4096-byte physical blocks
[  514.001488] sd 11:0:0:0: [sdb] Write Protect is off
[  514.001492] sd 11:0:0:0: [sdb] Mode Sense: 4f 00 00 00
[  514.001638] sd 11:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[  516.080393]  sdb: sdb1
[  516.081744] sd 11:0:0:0: [sdb] Attached SCSI disk
[  516.947836] usb 2-2: USB disconnect, device number 9
[  516.948257] sd 11:0:0:0: [sdb] Synchronizing SCSI cache
[  517.071106] sd 11:0:0:0: [sdb] Synchronize Cache(10) failed: Result: hostbyte=DID_ERROR driverbyte=DRIVER_OK[   33.024928] usb 2-1: new SuperSpeed USB device number 2 using xhci_hcd
[   33.043698] usb 2-1: New USB device found, idVendor=0bc2, idProduct=2321
[   33.043701] usb 2-1: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[   33.043702] usb 2-1: Product: Expansion
[   33.043703] usb 2-1: Manufacturer: Seagate 
[   33.043705] usb 2-1: SerialNumber: NA4AT906
[   33.055276] usb-storage 2-1:1.0: USB Mass Storage device detected
[   33.055796] scsi host4: usb-storage 2-1:1.0
[   33.055897] usbcore: registered new interface driver usb-storage
[   33.057513] usbcore: registered new interface driver uas
[   34.053914] scsi 4:0:0:0: Direct-Access     Seagate  Expansion        0219 PQ: 0 ANSI: 6
[   34.054233] sd 4:0:0:0: Attached scsi generic sg1 type 0
[   55.120163] sd 4:0:0:0: [sdb] Spinning up disk...
[   59.640823] usb 2-1: Disable of device-initiated U1 failed.
[   59.644262] usb 2-1: Disable of device-initiated U2 failed.
[   60.367518] usb 2-1: USB disconnect, device number 2
[   61.380448] .ready
[   61.380624] sd 4:0:0:0: [sdb] Read Capacity(10) failed: Result: hostbyte=DID_NO_CONNECT driverbyte=DRIVER_OK
[   61.380628] sd 4:0:0:0: [sdb] Sense not available.
[   61.380662] sd 4:0:0:0: [sdb] Write Protect is off
[   61.380673] sd 4:0:0:0: [sdb] Mode Sense: 00 00 00 00
[   61.380709] sd 4:0:0:0: [sdb] Asking for cache data failed
[   61.380722] sd 4:0:0:0: [sdb] Assuming drive cache: write through
[   61.381302] sd 4:0:0:0: [sdb] Read Capacity(10) failed: Result: hostbyte=DID_NO_CONNECT driverbyte=DRIVER_OK
[   61.381304] sd 4:0:0:0: [sdb] Sense not available.
[   61.381317] sd 4:0:0:0: [sdb] Attached SCSI disk
[  116.391733] systemd[1]: apt-daily.timer: Adding 17min 55.120014s random time.
[  180.155884] usb 2-1: new SuperSpeed USB device number 3 using xhci_hcd
[  180.172597] usb 2-1: New USB device found, idVendor=0bc2, idProduct=2321
[  180.172601] usb 2-1: New USB device strings: Mfr=2, Product=3, SerialNumber=1
[  180.172603] usb 2-1: Product: Expansion
[  180.172605] usb 2-1: Manufacturer: Seagate
[  180.172607] usb 2-1: SerialNumber: 2HC015KJ
[  180.174591] scsi host5: uas
[  180.176468] scsi 5:0:0:0: Direct-Access     Seagate  Expansion        0502 PQ: 0 ANSI: 6
[  180.176973] sd 5:0:0:0: Attached scsi generic sg1 type 0
[  180.177288] sd 5:0:0:0: [sdb] Spinning up disk...
[  181.178895] ................................................................................
[  261.140098] usb 2-1: USB disconnect, device number 3
[  261.426865] .ready
[  261.586851] sd 5:0:0:0: [sdb] Read Capacity(16) failed: Result: hostbyte=DID_ERROR driverbyte=DRIVER_OK
[  261.586854] sd 5:0:0:0: [sdb] Sense not available.
[  261.706802] sd 5:0:0:0: [sdb] Read Capacity(10) failed: Result: hostbyte=DID_ERROR driverbyte=DRIVER_OK
[  261.706806] sd 5:0:0:0: [sdb] Sense not available.
[  261.794720] sd 5:0:0:0: [sdb] Write Protect is off
[  261.794723] sd 5:0:0:0: [sdb] Mode Sense: 00 00 00 00
[  261.834688] sd 5:0:0:0: [sdb] Asking for cache data failed
[  261.834692] sd 5:0:0:0: [sdb] Assuming drive cache: write through
[  262.062590] sd 5:0:0:0: [sdb] Read Capacity(16) failed: Result: hostbyte=DID_ERROR driverbyte=DRIVER_OK
[  262.062594] sd 5:0:0:0: [sdb] Sense not available.
[  262.182519] sd 5:0:0:0: [sdb] Read Capacity(10) failed: Result: hostbyte=DID_ERROR driverbyte=DRIVER_OK
[  262.182522] sd 5:0:0:0: [sdb] Sense not available.
[  262.422368] sd 5:0:0:0: [sdb] Attached SCSI disk
[  275.958597] usb 2-2: new SuperSpeed USB device number 4 using xhci_hcd
[  275.975347] usb 2-2: New USB device found, idVendor=0bc2, idProduct=2321
[  275.975351] usb 2-2: New USB device strings: Mfr=2, Product=3, SerialNumber=1
[  275.975353] usb 2-2: Product: Expansion
[  275.975355] usb 2-2: Manufacturer: Seagate
[  275.975356] usb 2-2: SerialNumber: 2HC015KJ
[  275.977125] scsi host6: uas
[  275.977598] scsi 6:0:0:0: Direct-Access     Seagate  Expansion        0502 PQ: 0 ANSI: 6
[  275.978151] sd 6:0:0:0: Attached scsi generic sg1 type 0
[  275.978258] sd 6:0:0:0: [sdb] Spinning up disk...
[  276.977994] ...................................................................................................
[  376.245447] usb 2-2: USB disconnect, device number 4
[  376.245528] sd 6:0:0:0: tag#0 uas_zap_pending 0 uas-tag 1 inflight: CMD 
[  376.245531] sd 6:0:0:0: tag#0 CDB: Test Unit Ready 00 00 00 00 00 00
[  376.245554] ready
[  376.361931] sd 6:0:0:0: [sdb] Read Capacity(16) failed: Result: hostbyte=DID_ERROR driverbyte=DRIVER_OK
[  376.361935] sd 6:0:0:0: [sdb] Sense not available.
[  376.482049] sd 6:0:0:0: [sdb] Read Capacity(10) failed: Result: hostbyte=DID_ERROR driverbyte=DRIVER_OK
[  376.482052] sd 6:0:0:0: [sdb] Sense not available.
[  376.570129] sd 6:0:0:0: [sdb] Write Protect is off
[  376.570132] sd 6:0:0:0: [sdb] Mode Sense: 00 00 00 00
[  376.610165] sd 6:0:0:0: [sdb] Asking for cache data failed
[  376.610169] sd 6:0:0:0: [sdb] Assuming drive cache: write through
[  376.842367] sd 6:0:0:0: [sdb] Read Capacity(16) failed: Result: hostbyte=DID_ERROR driverbyte=DRIVER_OK
[  376.842370] sd 6:0:0:0: [sdb] Sense not available.
[  376.962439] sd 6:0:0:0: [sdb] Read Capacity(10) failed: Result: hostbyte=DID_ERROR driverbyte=DRIVER_OK
[  376.962442] sd 6:0:0:0: [sdb] Sense not available.
[  377.162638] sd 6:0:0:0: [sdb] Attached SCSI disk
[  383.263500] usb 2-2: new SuperSpeed USB device number 5 using xhci_hcd
[  383.280228] usb 2-2: New USB device found, idVendor=0bc2, idProduct=2321
[  383.280232] usb 2-2: New USB device strings: Mfr=2, Product=3, SerialNumber=1
[  383.280234] usb 2-2: Product: Expansion
[  383.280236] usb 2-2: Manufacturer: Seagate
[  383.280238] usb 2-2: SerialNumber: 2HC015KJ
[  383.282026] scsi host7: uas
[  383.283790] scsi 7:0:0:0: Direct-Access     Seagate  Expansion        0502 PQ: 0 ANSI: 6
[  383.284411] sd 7:0:0:0: Attached scsi generic sg1 type 0
[  383.284438] sd 7:0:0:0: [sdb] Spinning up disk...
[  384.288132] ..............................
[  414.341158] usb 2-2: USB disconnect, device number 5
[  414.426199] .ready
[  414.586320] sd 7:0:0:0: [sdb] Read Capacity(16) failed: Result: hostbyte=DID_ERROR driverbyte=DRIVER_OK
[  414.586323] sd 7:0:0:0: [sdb] Sense not available.
[  414.706355] sd 7:0:0:0: [sdb] Read Capacity(10) failed: Result: hostbyte=DID_ERROR driverbyte=DRIVER_OK
[  414.706360] sd 7:0:0:0: [sdb] Sense not available.
[  414.794375] sd 7:0:0:0: [sdb] Write Protect is off
[  414.794379] sd 7:0:0:0: [sdb] Mode Sense: 00 00 00 00
[  414.834391] sd 7:0:0:0: [sdb] Asking for cache data failed
[  414.834395] sd 7:0:0:0: [sdb] Assuming drive cache: write through
[  415.062455] sd 7:0:0:0: [sdb] Read Capacity(16) failed: Result: hostbyte=DID_ERROR driverbyte=DRIVER_OK
[  415.062458] sd 7:0:0:0: [sdb] Sense not available.
[  415.182491] sd 7:0:0:0: [sdb] Read Capacity(10) failed: Result: hostbyte=DID_ERROR driverbyte=DRIVER_OK
[  415.182495] sd 7:0:0:0: [sdb] Sense not available.
[  415.382544] sd 7:0:0:0: [sdb] Attached SCSI disk
[  436.159245] usb 2-2: new SuperSpeed USB device number 6 using xhci_hcd
[  436.175831] usb 2-2: New USB device found, idVendor=0bc2, idProduct=2321
[  436.175834] usb 2-2: New USB device strings: Mfr=2, Product=3, SerialNumber=1
[  436.175836] usb 2-2: Product: Expansion
[  436.175837] usb 2-2: Manufacturer: Seagate
[  436.175838] usb 2-2: SerialNumber: 2HC015KJ
[  436.177490] scsi host8: uas
[  436.178528] scsi 8:0:0:0: Direct-Access     Seagate  Expansion        0502 PQ: 0 ANSI: 6
[  436.179064] sd 8:0:0:0: Attached scsi generic sg1 type 0
[  436.179388] sd 8:0:0:0: [sdb] Spinning up disk...
[  437.183342] ..ready
[  438.187867] sd 8:0:0:0: [sdb] 1953525167 512-byte logical blocks: (1.00 TB/932 GiB)
[  438.187871] sd 8:0:0:0: [sdb] 2048-byte physical blocks
[  438.401354] sd 8:0:0:0: [sdb] Write Protect is off
[  438.401359] sd 8:0:0:0: [sdb] Mode Sense: 4f 00 00 00
[  438.404691] usb 2-2: cmd cmplt err -71
[  438.404695] xhci_hcd 0000:00:14.0: ERROR Transfer event for disabled endpoint or incorrect stream ring
[  438.404698] xhci_hcd 0000:00:14.0: @000000003fb70700 00000000 00000000 04000000 08078001
[  439.135787] usb 2-2: USB disconnect, device number 6
[  439.136027] sd 8:0:0:0: tag#0 uas_zap_pending 0 uas-tag 1 inflight: CMD 
[  439.136036] sd 8:0:0:0: tag#0 CDB: Mode Sense(6) 1a 00 08 00 04 00
[  439.136109] sd 8:0:0:0: [sdb] Asking for cache data failed
[  439.136119] sd 8:0:0:0: [sdb] Assuming drive cache: write through
[  439.363764] sd 8:0:0:0: [sdb] Read Capacity(16) failed: Result: hostbyte=DID_ERROR driverbyte=DRIVER_OK
[  439.363767] sd 8:0:0:0: [sdb] Sense not available.
[  439.483784] sd 8:0:0:0: [sdb] Read Capacity(10) failed: Result: hostbyte=DID_ERROR driverbyte=DRIVER_OK
[  439.483787] sd 8:0:0:0: [sdb] Sense not available.
[  439.723819] sd 8:0:0:0: [sdb] Attached SCSI disk
[  453.361652] usb 2-2: new SuperSpeed USB device number 7 using xhci_hcd
[  453.378371] usb 2-2: New USB device found, idVendor=0bc2, idProduct=2321
[  453.378373] usb 2-2: New USB device strings: Mfr=2, Product=3, SerialNumber=1
[  453.378375] usb 2-2: Product: Expansion
[  453.378376] usb 2-2: Manufacturer: Seagate
[  453.378377] usb 2-2: SerialNumber: NA4AT906
[  453.380046] scsi host9: uas
[  453.380499] scsi 9:0:0:0: Direct-Access     Seagate  Expansion        0502 PQ: 0 ANSI: 6
[  453.381082] sd 9:0:0:0: [sdb] 1953525167 512-byte logical blocks: (1.00 TB/932 GiB)
[  453.381084] sd 9:0:0:0: [sdb] 4096-byte physical blocks
[  453.381695] sd 9:0:0:0: Attached scsi generic sg1 type 0
[  453.842067] sd 9:0:0:0: [sdb] Write Protect is off
[  453.842071] sd 9:0:0:0: [sdb] Mode Sense: 4f 00 00 00
[  453.842272] sd 9:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[  453.853509]  sdb: sdb1
[  453.854847] sd 9:0:0:0: [sdb] Attached SCSI disk
[  501.001736] sd 9:0:0:0: [sdb] Synchronizing SCSI cache
[  501.118525] sd 9:0:0:0: [sdb] Synchronize Cache(10) failed: Result: hostbyte=DID_ERROR driverbyte=DRIVER_OK
[  501.153024] usb 2-2: USB disconnect, device number 7
[  501.527014] usb 2-2: new SuperSpeed USB device number 8 using xhci_hcd
[  501.543688] usb 2-2: New USB device found, idVendor=0bc2, idProduct=2321
[  501.543690] usb 2-2: New USB device strings: Mfr=2, Product=3, SerialNumber=1
[  501.543692] usb 2-2: Product: Expansion
[  501.543693] usb 2-2: Manufacturer: Seagate
[  501.543694] usb 2-2: SerialNumber: NA4AT906
[  501.545329] scsi host10: uas
[  501.546356] scsi 10:0:0:0: Direct-Access     Seagate  Expansion        0502 PQ: 0 ANSI: 6
[  501.546876] sd 10:0:0:0: Attached scsi generic sg1 type 0
[  501.547082] sd 10:0:0:0: [sdb] 1953525167 512-byte logical blocks: (1.00 TB/932 GiB)
[  501.547085] sd 10:0:0:0: [sdb] 4096-byte physical blocks
[  501.547394] sd 10:0:0:0: [sdb] Write Protect is off
[  501.547397] sd 10:0:0:0: [sdb] Mode Sense: 4f 00 00 00
[  501.547554] sd 10:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[  503.618587]  sdb: sdb1
[  503.619863] sd 10:0:0:0: [sdb] Attached SCSI disk
[  513.448650] sd 10:0:0:0: [sdb] Synchronizing SCSI cache
[  513.571824] sd 10:0:0:0: [sdb] Synchronize Cache(10) failed: Result: hostbyte=DID_ERROR driverbyte=DRIVER_OK
[  513.604864] usb 2-2: USB disconnect, device number 8
[  513.980307] usb 2-2: new SuperSpeed USB device number 9 using xhci_hcd
[  513.996960] usb 2-2: New USB device found, idVendor=0bc2, idProduct=2321
[  513.996962] usb 2-2: New USB device strings: Mfr=2, Product=3, SerialNumber=1
[  513.996964] usb 2-2: Product: Expansion
[  513.996965] usb 2-2: Manufacturer: Seagate
[  513.996966] usb 2-2: SerialNumber: NA4AT906
[  513.998656] scsi host11: uas
[  513.999666] scsi 11:0:0:0: Direct-Access     Seagate  Expansion        0502 PQ: 0 ANSI: 6
[  514.000116] sd 11:0:0:0: Attached scsi generic sg1 type 0
[  514.000871] sd 11:0:0:0: [sdb] 1953525167 512-byte logical blocks: (1.00 TB/932 GiB)
[  514.000873] sd 11:0:0:0: [sdb] 4096-byte physical blocks
[  514.001488] sd 11:0:0:0: [sdb] Write Protect is off
[  514.001492] sd 11:0:0:0: [sdb] Mode Sense: 4f 00 00 00
[  514.001638] sd 11:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[  516.080393]  sdb: sdb1
[  516.081744] sd 11:0:0:0: [sdb] Attached SCSI disk
[  516.947836] usb 2-2: USB disconnect, device number 9
[  516.948257] sd 11:0:0:0: [sdb] Synchronizing SCSI cache
[  517.071106] sd 11:0:0:0: [sdb] Synchronize Cache(10) failed: Result: hostbyte=DID_ERROR driverbyte=DRIVER_OK

C'est assez long et j'apprécierais vraiment que quelqu'un lise ce qui précède pour me dire quel est le problème avec le disque.

J'ai des informations assez mémorables ainsi que des informations sensibles, pour que je tente de les récupérer auprès d'une entreprise professionnelle et j'aimerais le faire moi-même.

Toute aide est vraiment appréciée.

Merci.

Demandé el 20 de Décembre, 2016 par Mike Wazowski

Réponses

Trop de publicités?

1voto

stepank avatar
stepank Points 376

Avez-vous essayé la commande ntfsfix ? Parfois, le disque n'est pas correctement sorti sous Windows et vous devez le corriger avant de lire le disque.

Répondu el 20 de Décembre, 2016 par stepank (376 Points )

1voto

ridgy avatar
ridgy Points 2086

Si le disque est un disque 2" sans alimentation externe ("Expansion Portable"), l'une des raisons peut être qu'il n'y a pas assez de puissance pour faire tourner le disque lorsqu'il est alimenté par USB, voir le message

[  180.177288] sd 5:0:0:0: [sdb] Spinning up disk...
[  181.178895] ................................................................................
[  261.140098] usb 2-1: USB disconnect, device number 3

Dans ce cas, un HUB USB à alimentation active peut être utile.

S'il est alimenté par sa propre alimentation ("Expansion Desktop"), il semble que le disque soit corrompu d'une manière ou d'une autre. Comme il peut s'agir également du contrôleur SATA-to-USB, il reste une chance de récupérer les données si le disque lui-même fonctionne encore :

  • Ouvrez délicatement le boîtier (il se peut que des vis soient cachées par des amortisseurs en caoutchouc).
  • Sortez délicatement le disque du boîtier
  • Procurez-vous un autre adaptateur SATA-USB avec votre propre alimentation et essayez-le.
  • Ou mieux : Si votre PC dispose d'un port SATA inutilisé, connectez-y le disque (ainsi que la ligne d'alimentation) et essayez. Dans ce cas, l'outil GSmartControl peut aider, car SMART est pris en charge par les disques modernes lorsqu'ils sont connectés via SATA (ne fonctionne généralement pas via USB).

SMART est un moyen de lire des informations sur l'état du disque et les erreurs survenues. Les informations sur la façon d'utiliser GSmartControl voir par exemple https://www.technibble.com/gsmartcontrol-monitor-test-hard-drive-smart-data/

Répondu el 21 de Décembre, 2016 par ridgy (2086 Points )

Questions en vedette

Top Tags

Dans notre réseau

SistemesEz.com

SystemesEZ est une communauté de sysadmins où vous pouvez résoudre vos problèmes et vos doutes. Vous pouvez consulter les questions des autres sysadmins, poser vos propres questions ou résoudre celles des autres.

Powered by:

Yandex
X