J'ai des problèmes pour monter ma clé usb3.0 de 16 Go à la fois sous Windows 7 et sous Ubuntu 14.04.
Le périphérique n'apparaît pas sur fdisk ou quand je lance lsusb.
Voici ce que j'obtiens lorsque je lance dmesg après l'avoir branché. Toute aide sera grandement appréciée.
Je ne sais pas si c'est lié, mais la première fois que j'ai essayé de l'utiliser, j'ai eu un crash sous ubuntu.
[ 55.768914] usb 3-1: new high-speed USB device number 2 using xhci_hcd
[ 55.795584] usb 3-1: New USB device found, idVendor=058f, idProduct=6387
[ 55.795595] usb 3-1: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[ 55.795601] usb 3-1: Product: Mass Storage
[ 55.795605] usb 3-1: Manufacturer: Generic
[ 55.795609] usb 3-1: SerialNumber: FA8EDD26
[ 55.823608] usb-storage 3-1:1.0: USB Mass Storage device detected
[ 55.823756] scsi6 : usb-storage 3-1:1.0
[ 55.823807] usbcore: registered new interface driver usb-storage
[ 56.821322] scsi 6:0:0:0: Direct-Access Generic Flash Disk 8.07 PQ: 0 ANSI: 4
[ 56.821674] sd 6:0:0:0: Attached scsi generic sg2 type 0
[ 56.822304] sd 6:0:0:0: [sdb] 15663104 512-byte logical blocks: (8.01 GB/7.46 GiB)
[ 56.823547] sd 6:0:0:0: [sdb] Write Protect is off
[ 56.823551] sd 6:0:0:0: [sdb] Mode Sense: 23 00 00 00
[ 56.824208] sd 6:0:0:0: [sdb] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA
[ 56.828139] sdb:
[ 56.830093] sd 6:0:0:0: [sdb] Attached SCSI removable disk
[ 57.247388] systemd-hostnamed[2500]: Warning: nss-myhostname is not installed. Changing the local hostname might make it unresolveable. Please install nss-myhostname!
[ 356.974918] sdb: detected capacity change from 8019509248 to 0
[ 358.897899] usb 3-1: USB disconnect, device number 2
[ 367.270539] usb 3-1: new high-speed USB device number 3 using xhci_hcd
[ 367.295406] usb 3-1: New USB device found, idVendor=090c, idProduct=1000
[ 367.295417] usb 3-1: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[ 367.295423] usb 3-1: Product: Silicon-Power
[ 367.295427] usb 3-1: Manufacturer: UFD 3.0
[ 367.295431] usb 3-1: SerialNumber: 1401353601000000
[ 367.297277] usb-storage 3-1:1.0: USB Mass Storage device detected
[ 367.297632] scsi7 : usb-storage 3-1:1.0
[ 368.526818] scsi 7:0:0:0: Direct-Access UFD 3.0 Silicon-Power16G 1100 PQ: 0 ANSI: 6
[ 368.527609] sd 7:0:0:0: Attached scsi generic sg2 type 0
[ 368.528638] sd 7:0:0:0: [sdb] 30556160 512-byte logical blocks: (15.6 GB/14.5 GiB)
[ 368.529634] sd 7:0:0:0: [sdb] Write Protect is off
[ 368.529644] sd 7:0:0:0: [sdb] Mode Sense: 43 00 00 00
[ 368.530660] sd 7:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 368.539830] sdb: sdb1
[ 368.543535] sd 7:0:0:0: [sdb] Attached SCSI removable disk
[ 399.379753] usb 3-1: reset high-speed USB device number 3 using xhci_hcd
[ 404.371128] xhci_hcd 0000:04:00.0: Timeout while waiting for address device command
[ 404.575354] usb 3-1: Device not responding to set address.
[ 404.778430] usb 3-1: device not accepting address 3, error -71
[ 404.890571] usb 3-1: reset high-speed USB device number 3 using xhci_hcd
[ 409.882324] xhci_hcd 0000:04:00.0: Timeout while waiting for address device command
[ 410.086603] usb 3-1: Device not responding to set address.
[ 410.289609] usb 3-1: device not accepting address 3, error -71
[ 410.401702] usb 3-1: reset high-speed USB device number 3 using xhci_hcd
[ 410.402319] usb 3-1: Device not responding to set address.
[ 410.605655] usb 3-1: Device not responding to set address.
[ 410.808785] usb 3-1: device not accepting address 3, error -71
[ 410.920897] usb 3-1: reset high-speed USB device number 3 using xhci_hcd
[ 410.921521] usb 3-1: Device not responding to set address.
[ 411.124768] usb 3-1: Device not responding to set address.
[ 411.327929] usb 3-1: device not accepting address 3, error -71
[ 411.328474] usb 3-1: USB disconnect, device number 3
[ 411.328501] sd 7:0:0:0: Device offlined - not ready after error recovery
[ 411.328517] sd 7:0:0:0: [sdb] Unhandled error code
[ 411.328518] sd 7:0:0:0: [sdb]
[ 411.328520] Result: hostbyte=DID_ABORT driverbyte=DRIVER_OK
[ 411.328521] sd 7:0:0:0: [sdb] CDB:
[ 411.328522] Read(10): 28 00 00 00 01 40 00 00 08 00
[ 411.328527] end_request: I/O error, dev sdb, sector 320
[ 411.328530] Buffer I/O error on device sdb, logical block 40
[ 411.328731] sdb: detected capacity change from 15644753920 to 0
[ 411.329448] xhci_hcd 0000:04:00.0: xHCI xhci_drop_endpoint called with disabled ep ffff88019c0be180
[ 411.329452] xhci_hcd 0000:04:00.0: xHCI xhci_drop_endpoint called with disabled ep ffff88019c0be1c0
[ 411.439824] usb 3-1: new high-speed USB device number 4 using xhci_hcd
[ 411.440048] usb 3-1: Device not responding to set address.
[ 411.643676] usb 3-1: Device not responding to set address.
[ 411.847114] usb 3-1: device not accepting address 4, error -71
[ 411.959016] usb 3-1: new high-speed USB device number 5 using xhci_hcd
[ 411.959230] usb 3-1: Device not responding to set address.
[ 412.162785] usb 3-1: Device not responding to set address.
[ 412.366291] usb 3-1: device not accepting address 5, error -71
[ 412.478060] usb 3-1: new high-speed USB device number 6 using xhci_hcd
[ 412.478261] usb 3-1: Device not responding to set address.
[ 412.682029] usb 3-1: Device not responding to set address.
[ 412.885437] usb 3-1: device not accepting address 6, error -71
[ 412.997353] usb 3-1: new high-speed USB device number 7 using xhci_hcd
[ 412.997598] usb 3-1: Device not responding to set address.
[ 413.201089] usb 3-1: Device not responding to set address.
[ 413.404490] usb 3-1: device not accepting address 7, error -71
[ 413.404561] hub 3-0:1.0: unable to enumerate USB device on port 1
[ 646.768145] usb 4-2: new SuperSpeed USB device number 2 using xhci_hcd
[ 646.786437] usb 4-2: Parent hub missing LPM exit latency info. Power management will be impacted.
[ 646.790960] usb 4-2: New USB device found, idVendor=090c, idProduct=1000
[ 646.790972] usb 4-2: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[ 646.790977] usb 4-2: Product: Silicon-Power
[ 646.790981] usb 4-2: Manufacturer: UFD 3.0
[ 646.790985] usb 4-2: SerialNumber: 1401353601000000
[ 646.792857] usb-storage 4-2:1.0: USB Mass Storage device detected
[ 646.793286] scsi8 : usb-storage 4-2:1.0
[ 647.980627] scsi 8:0:0:0: Direct-Access UFD 3.0 Silicon-Power16G 1100 PQ: 0 ANSI: 6
[ 647.981319] sd 8:0:0:0: Attached scsi generic sg2 type 0
[ 647.982580] sd 8:0:0:0: [sdb] 30556160 512-byte logical blocks: (15.6 GB/14.5 GiB)
[ 647.983466] sd 8:0:0:0: [sdb] Write Protect is off
[ 647.983479] sd 8:0:0:0: [sdb] Mode Sense: 43 00 00 00
[ 647.984442] sd 8:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 647.994070] sdb: sdb1
[ 647.997460] sd 8:0:0:0: [sdb] Attached SCSI removable disk
[ 683.923838] xhci_hcd 0000:04:00.0: Timeout while waiting for address device command
[ 689.119486] xhci_hcd 0000:04:00.0: Timeout while waiting for address device command
[ 689.323245] usb 4-2: device not accepting address 2, error -62
[ 689.844066] sd 8:0:0:0: Device offlined - not ready after error recovery
[ 689.844089] sd 8:0:0:0: [sdb] Unhandled error code
[ 689.844094] sd 8:0:0:0: [sdb]
[ 689.844098] Result: hostbyte=DID_ABORT driverbyte=DRIVER_OK
[ 689.844102] sd 8:0:0:0: [sdb] CDB:
[ 689.844105] Read(10): 28 00 00 00 03 40 00 00 08 00
[ 689.844122] end_request: I/O error, dev sdb, sector 832
[ 689.844130] Buffer I/O error on device sdb, logical block 104
[ 689.844156] sd 8:0:0:0: rejecting I/O to offline device
[ 689.844164] sd 8:0:0:0: killing request
[ 689.844207] usb 4-2: USB disconnect, device number 2
[ 689.846504] xhci_hcd 0000:04:00.0: xHCI xhci_drop_endpoint called with disabled ep ffff880222872380
[ 689.846507] xhci_hcd 0000:04:00.0: xHCI xhci_drop_endpoint called with disabled ep ffff8802228723c0
[ 902.274572] usb 3-1: new high-speed USB device number 9 using xhci_hcd
[ 902.293221] usb 3-1: New USB device found, idVendor=1043, idProduct=8012
[ 902.293232] usb 3-1: New USB device strings: Mfr=1, Product=2, SerialNumber=0
[ 902.293237] usb 3-1: Product: Flash Disk
[ 902.293241] usb 3-1: Manufacturer: Generic
[ 902.294415] usb-storage 3-1:1.0: USB Mass Storage device detected
[ 902.294674] scsi9 : usb-storage 3-1:1.0
[ 903.293930] scsi 9:0:0:0: Direct-Access Generic USB Flash Drive 1.00 PQ: 0 ANSI: 2
[ 903.294720] sd 9:0:0:0: Attached scsi generic sg2 type 0
[ 903.295065] sd 9:0:0:0: [sdb] 2048001 512-byte logical blocks: (1.04 GB/1000 MiB)
[ 903.295317] sd 9:0:0:0: [sdb] Write Protect is off
[ 903.295325] sd 9:0:0:0: [sdb] Mode Sense: 03 00 00 00
[ 903.295568] sd 9:0:0:0: [sdb] No Caching mode page found
[ 903.295575] sd 9:0:0:0: [sdb] Assuming drive cache: write through
[ 903.297265] sd 9:0:0:0: [sdb] No Caching mode page found
[ 903.297271] sd 9:0:0:0: [sdb] Assuming drive cache: write through
[ 903.302919] sdb: sdb1
[ 903.304247] sd 9:0:0:0: [sdb] No Caching mode page found
[ 903.304256] sd 9:0:0:0: [sdb] Assuming drive cache: write through
[ 903.304262] sd 9:0:0:0: [sdb] Attached SCSI removable disk
[ 903.554797] systemd-hostnamed[3195]: Warning: nss-myhostname is not installed. Changing the local hostname might make it unresolveable. Please install nss-myhostname!
[ 924.855781] usb 3-1: USB disconnect, device number 9
[ 924.878581] FAT-fs (sdb1): unable to read boot sector to mark fs as dirty
[ 933.681129] usb 4-1: new SuperSpeed USB device number 3 using xhci_hcd
[ 933.699432] usb 4-1: Parent hub missing LPM exit latency info. Power management will be impacted.
[ 933.704230] usb 4-1: New USB device found, idVendor=090c, idProduct=1000
[ 933.704241] usb 4-1: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[ 933.704247] usb 4-1: Product: Silicon-Power
[ 933.704251] usb 4-1: Manufacturer: UFD 3.0
[ 933.704255] usb 4-1: SerialNumber: 1401353601000000
[ 933.706022] usb-storage 4-1:1.0: USB Mass Storage device detected
[ 933.706371] scsi10 : usb-storage 4-1:1.0
[ 934.893676] scsi 10:0:0:0: Direct-Access UFD 3.0 Silicon-Power16G 1100 PQ: 0 ANSI: 6
[ 934.895563] sd 10:0:0:0: [sdb] 30556160 512-byte logical blocks: (15.6 GB/14.5 GiB)
[ 934.895999] sd 10:0:0:0: Attached scsi generic sg2 type 0
[ 934.896523] sd 10:0:0:0: [sdb] Write Protect is off
[ 934.896544] sd 10:0:0:0: [sdb] Mode Sense: 43 00 00 00
[ 934.897405] sd 10:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 934.905207] sdb: sdb1
[ 934.908923] sd 10:0:0:0: [sdb] Attached SCSI removable disk
[ 970.505295] xhci_hcd 0000:04:00.0: Timeout while waiting for address device command
[ 975.701085] xhci_hcd 0000:04:00.0: Timeout while waiting for address device command
[ 975.904630] usb 4-1: device not accepting address 3, error -62
[ 976.425379] usb 4-1: USB disconnect, device number 3
[ 976.425395] sd 10:0:0:0: Device offlined - not ready after error recovery
[ 976.425402] sd 10:0:0:0: [sdb] Unhandled error code
[ 976.425404] sd 10:0:0:0: [sdb]
[ 976.425405] Result: hostbyte=DID_ABORT driverbyte=DRIVER_OK
[ 976.425406] sd 10:0:0:0: [sdb] CDB:
[ 976.425407] Read(10): 28 00 00 00 03 40 00 00 08 00
[ 976.425412] end_request: I/O error, dev sdb, sector 832
[ 976.425415] Buffer I/O error on device sdb, logical block 104
[ 976.425616] sdb: detected capacity change from 15644753920 to 0
[ 976.425866] xhci_hcd 0000:04:00.0: xHCI xhci_drop_endpoint called with disabled ep ffff88019c0be900
[ 976.425868] xhci_hcd 0000:04:00.0: xHCI xhci_drop_endpoint called with disabled ep ffff88019c0be940
