J'ai installé Ubuntu 12.10 sur un Sony VIAO E Series VPCEH16EN, 4GB RAM, 320 GB HDD, Intel Core i3-2310M Processor 2.10GHz. Il s'agit d'un dual boot avec Windows7 en parallèle.
Je vois que le système est très lent à répondre, toute vidéo reste bloquée entre la lecture. Pouvez-vous m'aider à trouver où se trouve le goulot d'étranglement ? Voici la sortie de hdparm y smartctl :
------------- HDPARM -------------------
anil@anil-ubuntu:~$ sudo hdparm -Tt /dev/sda6
/dev/sda6:
Timing cached reads: 2 MB in 3.51 seconds = 584.17 kB/sec
Timing buffered disk reads: 160 MB in 3.02 seconds = 52.91 MB/sec
anil@anil-ubuntu:~$
-----------------------------------------
-------------- SMARTCTL -----------------
anil@anil-ubuntu:~$ sudo smartctl -a /dev/sda6
smartctl 5.43 2012-06-30 r3573 [x86_64-linux-3.5.0-25-generic] (local build)
Copyright (C) 2002-12 by Bruce Allen, http://smartmontools.sourceforge.net
=== START OF INFORMATION SECTION ===
Device Model: TOSHIBA MK3265GSXN
Serial Number: 419CD3X3B
LU WWN Device Id: 5 000039 33ab02a3c
Firmware Version: GH012H
User Capacity: 320,072,933,376 bytes [320 GB]
Sector Size: 512 bytes logical/physical
Device is: Not in smartctl database [for details use: -P showall]
ATA Version is: 8
ATA Standard is: Exact ATA specification draft version not indicated
Local Time is: Thu Feb 28 23:08:07 2013 IST
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED
General SMART Values:
Offline data collection status: (0x00) Offline data collection activity
was never started.
Auto Offline Data Collection: Disabled.
Self-test execution status: ( 0) The previous self-test routine completed
without error or no self-test has ever
been run.
Total time to complete Offline
data collection: ( 120) seconds.
Offline data collection
capabilities: (0x5b) SMART execute Offline immediate.
Auto Offline data collection on/off support.
Suspend Offline collection upon new
command.
Offline surface scan supported.
Self-test supported.
No Conveyance Self-test supported.
Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
General Purpose Logging supported.
Short self-test routine
recommended polling time: ( 2) minutes.
Extended self-test routine
recommended polling time: ( 95) minutes.
SCT capabilities: (0x003d) SCT Status supported.
SCT Error Recovery Control supported.
SCT Feature Control supported.
SCT Data Table supported.
SMART Attributes Data Structure revision number: 16
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE
1 Raw_Read_Error_Rate 0x000b 100 100 050 Pre-fail Always - 0
2 Throughput_Performance 0x0005 100 100 050 Pre-fail Offline - 0
3 Spin_Up_Time 0x0027 100 100 001 Pre-fail Always - 1258
4 Start_Stop_Count 0x0032 100 100 000 Old_age Always - 2560
5 Reallocated_Sector_Ct 0x0033 100 100 050 Pre-fail Always - 47
7 Seek_Error_Rate 0x000b 100 100 050 Pre-fail Always - 0
8 Seek_Time_Performance 0x0005 100 100 050 Pre-fail Offline - 0
9 Power_On_Hours 0x0032 088 088 000 Old_age Always - 4940
10 Spin_Retry_Count 0x0033 150 100 030 Pre-fail Always - 0
12 Power_Cycle_Count 0x0032 100 100 000 Old_age Always - 2553
191 G-Sense_Error_Rate 0x0032 100 100 000 Old_age Always - 118
192 Power-Off_Retract_Count 0x0032 100 100 000 Old_age Always - 169
193 Load_Cycle_Count 0x0032 099 099 000 Old_age Always - 13993
194 Temperature_Celsius 0x0022 100 100 000 Old_age Always - 43 (Min/Max 20/47)
196 Reallocated_Event_Count 0x0032 100 100 000 Old_age Always - 5
197 Current_Pending_Sector 0x0032 100 100 000 Old_age Always - 0
198 Offline_Uncorrectable 0x0030 100 100 000 Old_age Offline - 0
199 UDMA_CRC_Error_Count 0x0032 200 200 000 Old_age Always - 0
220 Disk_Shift 0x0002 100 100 000 Old_age Always - 19
222 Loaded_Hours 0x0032 091 091 000 Old_age Always - 3918
223 Load_Retry_Count 0x0032 100 100 000 Old_age Always - 0
224 Load_Friction 0x0022 100 100 000 Old_age Always - 0
226 Load-in_Time 0x0026 100 100 000 Old_age Always - 245
240 Head_Flying_Hours 0x0001 100 100 001 Pre-fail Offline - 0
SMART Error Log Version: 1
ATA Error Count: 108 (device log contains only the most recent five errors)
CR = Command Register [HEX]
FR = Features Register [HEX]
SC = Sector Count Register [HEX]
SN = Sector Number Register [HEX]
CL = Cylinder Low Register [HEX]
CH = Cylinder High Register [HEX]
DH = Device/Head Register [HEX]
DC = Device Command Register [HEX]
ER = Error register [HEX]
ST = Status register [HEX]
Powered_Up_Time is measured from power on, and printed as
DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes,
SS=sec, and sss=millisec. It "wraps" after 49.710 days.
Error 108 occurred at disk power-on lifetime: 3337 hours (139 days + 1 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 41 4a 6a 9d bb 64 Error: WP at LBA = 0x04bb9d6a = 79404394
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
61 08 58 f0 f6 b8 40 00 03:49:54.536 WRITE FPDMA QUEUED
61 08 50 00 f7 b8 40 00 03:49:54.536 WRITE FPDMA QUEUED
60 00 48 98 9c bb 40 00 03:49:54.535 READ FPDMA QUEUED
61 38 40 c8 0b b9 40 00 03:49:54.535 WRITE FPDMA QUEUED
61 02 38 88 3a 39 40 00 03:49:54.535 WRITE FPDMA QUEUED
Error 107 occurred at disk power-on lifetime: 3337 hours (139 days + 1 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 41 f2 6a 9d bb 64 Error: WP at LBA = 0x04bb9d6a = 79404394
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
61 08 f8 68 c9 65 40 00 03:49:50.336 WRITE FPDMA QUEUED
60 00 f0 98 9c bb 40 00 03:49:50.335 READ FPDMA QUEUED
61 08 e8 28 71 61 40 00 03:49:50.335 WRITE FPDMA QUEUED
61 18 e0 08 c8 61 40 00 03:49:50.335 WRITE FPDMA QUEUED
61 20 d8 d8 90 6c 40 00 03:49:50.335 WRITE FPDMA QUEUED
Error 106 occurred at disk power-on lifetime: 3337 hours (139 days + 1 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 41 62 6a 9d bb 64 Error: WP at LBA = 0x04bb9d6a = 79404394
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
61 08 70 f8 f6 b8 40 00 03:49:46.159 WRITE FPDMA QUEUED
61 08 68 08 f7 b8 40 00 03:49:46.159 WRITE FPDMA QUEUED
60 00 60 98 9c bb 40 00 03:49:46.157 READ FPDMA QUEUED
61 08 58 c0 0b b9 40 00 03:49:46.157 WRITE FPDMA QUEUED
61 08 50 e8 38 62 40 00 03:49:46.157 WRITE FPDMA QUEUED
Error 105 occurred at disk power-on lifetime: 3337 hours (139 days + 1 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 41 aa 6a 9d bb 64 Error: WP at LBA = 0x04bb9d6a = 79404394
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
61 08 00 28 87 7e 40 00 03:49:41.973 WRITE FPDMA QUEUED
61 08 f8 78 7d 7e 40 00 03:49:41.972 WRITE FPDMA QUEUED
61 08 f0 40 7d 7e 40 00 03:49:41.972 WRITE FPDMA QUEUED
61 08 e8 88 72 7e 40 00 03:49:41.972 WRITE FPDMA QUEUED
61 08 e0 d0 5e 7e 40 00 03:49:41.972 WRITE FPDMA QUEUED
Error 104 occurred at disk power-on lifetime: 3337 hours (139 days + 1 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 41 52 6a 9d bb 64 Error: WP at LBA = 0x04bb9d6a = 79404394
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
61 08 78 f0 04 bd 40 00 03:49:37.805 WRITE FPDMA QUEUED
61 08 70 20 03 bd 40 00 03:49:37.804 WRITE FPDMA QUEUED
61 08 68 08 03 bd 40 00 03:49:37.804 WRITE FPDMA QUEUED
61 10 60 e8 02 bd 40 00 03:49:37.803 WRITE FPDMA QUEUED
61 03 58 d8 f2 6f 40 00 03:49:37.803 WRITE FPDMA QUEUED
SMART Self-test log structure revision number 1
No self-tests have been logged. [To run self-tests, use: smartctl -t]
SMART Selective self-test log data structure revision number 1
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Not_testing
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.
--------------------------------------------------------------------
